Atlas PROJACK 35 3500 Pound Sliding Bridge Jack
5 Great reasons to buy from us:
Atlas 9KOHX 9000 Pound Overhead 2 Post Automotive Lift
5 Great reasons to buy from us:
The Atlas® RJ35 (3500 LB. capacity) sliding hydraulic bridge jack is the perfect choice for the owner of the Atlas® Garage PRO8000 or any of our other Atlas® Garage Pro lifts. The RJ35 Sliding Jack will also work on our other hobbyist four post lifts such as the ALI Certified Atlas® APEX8 and
Most four post hobbyist lifts come with a jack tray. The jack tray has certain limitations that are eliminated by using the Atlas® RJ35 Sliding Jack. The jack tray (with a small floor jack or jack stands) will support ONLY THOSE LIFTING POINTS of the raised vehicle that are between the runways of the four post lift. The RJ35 Sliding Jack has telescoping arms that can be extended over the runways of the four post lift. The lift pads at the end of these arms can be positioned under the LIFTING POINTS (that are located over the runways of the four post lift) of the vehicle allowing the operator to access many more LIFTING POINTS than just using the jack tray.
The Atlas® RJ35 Sliding Jack comes standard with a set of peg style truck adapters which increase the lifting height of the lift pads. These truck adapters will allow the RJ35 Sliding Jack sliding hydraulic jack to raise pick up trucks that will sit higher on the runways than the average passenger car. The RJ35 Sliding Jack is operated by a manual hydraulic pump (porta-power pump) and does not require an air compressor for power. This jack also features two solid locking positions that are used when the vehicle is to be suspended above the runways. When the locking positions of the Atlas® RJ35 Sliding Jack are engaged, the hydraulic pressure from the lifting cylinder of the jack is eliminated. (These locks act much like a pair of jack stands after you lift a vehicle off the ground with a service jack).
Finally, the versatile Atlas® RJ35 Sliding Jack is adjustable to fit between the runways of many of the other four post lifts that have been sold in the last several years.
Atlas® RJ35 Sliding Jack Specifications
- Capacity: 3500 lbs
- Lower Extension Width (Between Runway): 20 1/2" to 47"
- Top Width (Arms Retracted & Extended): 39 12" to 64 3/4"
- Min. Pad Height Above Runway (MAY VARY BY LIFT): 3 1/2"
- Lift Pad Height Above Arm: 1 3/8"
- Max Height Raised w/o Adapter: 11"
- Max Height Raised w/ Adapters: 17 1/4"
- Shipping Weight: 350 lbs
- Adapter Heights: 2 Each 1 1/2", 5"
- Arm Hole/Adapter Peg Size: 1 1/2"
Estimated between and
Will usually ship within 1 business day. Drop Ship will ship within 2 days.
 |
Please allow 3 to 8 days for your order to arrive. We stock most of our products and ship daily. This means there is minimal delays in your order. We also drop ship from multiple warehouses, this may take up to 2 days shipping. You will be notified with tracking information once product ships. Overnight shipping is available for an additional cost. Please contact us for information before placing an order. |
|
 |
Returns are easy, simply contact us for a returns number and send your item to our returns center for fast processing. We'll get you a replacement or refund in a snap! |
Returns are easy, simply contact us for a returns number and send your item to our returns center for fast processing. We'll get you a replacement or refund in a snap!
We insist that you love everything you buy from us. If you're unhappy for any reason whatsoever, just let us know and we'll bend over backwards to make things right again.
Ordering from Rocklands is 100% safe and secure so you can rest easy. Your personal details are never shared, sold or rented to anyone either.
Atlas 9KOHX 9000 Pound Overhead 2 Post Automotive Lift
5 Great reasons to buy from us:
The Atlas® RJ35 (3500 LB. capacity) sliding hydraulic bridge jack is the perfect choice for the owner of the Atlas® Garage PRO8000 or any of our other Atlas® Garage Pro lifts. The RJ35 Sliding Jack will also work on our other hobbyist four post lifts such as the ALI Certified Atlas® APEX8 and
Most four post hobbyist lifts come with a jack tray. The jack tray has certain limitations that are eliminated by using the Atlas® RJ35 Sliding Jack. The jack tray (with a small floor jack or jack stands) will support ONLY THOSE LIFTING POINTS of the raised vehicle that are between the runways of the four post lift. The RJ35 Sliding Jack has telescoping arms that can be extended over the runways of the four post lift. The lift pads at the end of these arms can be positioned under the LIFTING POINTS (that are located over the runways of the four post lift) of the vehicle allowing the operator to access many more LIFTING POINTS than just using the jack tray.
The Atlas® RJ35 Sliding Jack comes standard with a set of peg style truck adapters which increase the lifting height of the lift pads. These truck adapters will allow the RJ35 Sliding Jack sliding hydraulic jack to raise pick up trucks that will sit higher on the runways than the average passenger car. The RJ35 Sliding Jack is operated by a manual hydraulic pump (porta-power pump) and does not require an air compressor for power. This jack also features two solid locking positions that are used when the vehicle is to be suspended above the runways. When the locking positions of the Atlas® RJ35 Sliding Jack are engaged, the hydraulic pressure from the lifting cylinder of the jack is eliminated. (These locks act much like a pair of jack stands after you lift a vehicle off the ground with a service jack).
Finally, the versatile Atlas® RJ35 Sliding Jack is adjustable to fit between the runways of many of the other four post lifts that have been sold in the last several years.
Atlas® RJ35 Sliding Jack Specifications
- Capacity: 3500 lbs
- Lower Extension Width (Between Runway): 20 1/2" to 47"
- Top Width (Arms Retracted & Extended): 39 12" to 64 3/4"
- Min. Pad Height Above Runway (MAY VARY BY LIFT): 3 1/2"
- Lift Pad Height Above Arm: 1 3/8"
- Max Height Raised w/o Adapter: 11"
- Max Height Raised w/ Adapters: 17 1/4"
- Shipping Weight: 350 lbs
- Adapter Heights: 2 Each 1 1/2", 5"
- Arm Hole/Adapter Peg Size: 1 1/2"
Estimated between and
Will usually ship within 1 business day. Drop Ship will ship within 2 days.
|
Please allow 3 to 8 days for your order to arrive. We stock most of our products and ship daily. This means there is minimal delays in your order. We also drop ship from multiple warehouses, this may take up to 2 days shipping. You will be notified with tracking information once product ships. Overnight shipping is available for an additional cost. Please contact us for information before placing an order. |
|
|
Returns are easy, simply contact us for a returns number and send your item to our returns center for fast processing. We'll get you a replacement or refund in a snap! |
Returns are easy, simply contact us for a returns number and send your item to our returns center for fast processing. We'll get you a replacement or refund in a snap!
We insist that you love everything you buy from us. If you're unhappy for any reason whatsoever, just let us know and we'll bend over backwards to make things right again.
Ordering from Rocklands is 100% safe and secure so you can rest easy. Your personal details are never shared, sold or rented to anyone either.
